WiFi disabled in /etc/config/wireless. So it was disabled out of the box...


Hi,

I wonder if anyone can shed some light on this please. I've just received carambola+dev board and the wifi doesn't seem to be enabled. Is the wifi enabled out of the box or do I have to build a build root through menu config to enable to the wifi. Also, would anyone know if there is a ssh server running as I can't seem to ssh in. My only way in is via serial. However, i don't really fancy downloading a build root via serial!

Cheers

Ian



U-Boot 1.1.3 (Feb 20 2012 - 16:20:22)

Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb0000
config usb..
flash_protect ON: from 0xBF000000 to 0xBF01E757
flash_protect ON: from 0xBF030000 to 0xBF030FFF
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.5.0.0
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 256 Mbits SDR
DRAM bus: 16 bit
Total memory: 32 MBytes
Flash component: NOR Flash
Date:Feb 20 2012 Time:16:20:22
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 320 MHZ ####
estimate memory size =32 Mbytes

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0

3: System Boot system code via Flash.
## Booting image at bf050000 ...
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2012-10-29 16:27:44 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 872648 Bytes = 852.2 kB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[ 0.000000] Linux version 3.3.8 (zilvinas@LX-buildd3) (gcc version 4.7.1 20120402 (prerelease) (Linaro GCC 4.7-2012.04) ) #16 M
on Oct 29 18:27:35 EET 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] Ralink RT3350 id:1 rev:2 running at 320.00 MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=CARAMBOLA console=ttyS1,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00077ab0
[ 0.000000] Readback ErrCtl register=00077ab0
[ 0.000000] Memory: 29744k/32768k available (1991k kernel code, 3024k reserved, 328k data, 172k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.010000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
[ 0.090000] pid_max: default: 32768 minimum: 301
[ 0.090000] Mount-cache hash table entries: 512
[ 0.100000] NET: Registered protocol family 16
[ 0.110000] MIPS: machine is CARAMBOLA
[ 0.110000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0
[ 0.120000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1
[ 0.120000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2
[ 0.150000] bio: create slab <bio-0> at 0
[ 0.160000] Switching to clocksource MIPS
[ 0.170000] NET: Registered protocol family 2
[ 0.180000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.190000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.190000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.200000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.210000] TCP reno registered
[ 0.210000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.220000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.220000] NET: Registered protocol family 1
[ 0.280000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.280000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.290000] msgmni has been set to 58
[ 0.300000] io scheduler noop registered
[ 0.300000] io scheduler deadline registered (default)
[ 0.310000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.320000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[ 0.320000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.340000] physmap platform flash device: 00800000 at bf000000
[ 0.340000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022c9
[ 0.350000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.360000] Amd/Fujitsu Extended Query version 1.1.
[ 0.360000] physmap-flash.0: Swapping erase regions for top-boot CFI table.
[ 0.370000] number of CFI chips: 1
[ 0.370000] Creating 6 MTD partitions on "physmap-flash.0":
[ 0.380000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.390000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.400000] 0x000000040000-0x000000050000 : "factory"
[ 0.410000] 0x000000050000-0x000000170000 : "kernel"
[ 0.420000] 0x000000170000-0x000000800000 : "rootfs"
[ 0.430000] mtd: partition "rootfs" set to be root filesystem
[ 0.430000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=470000
[ 0.440000] 0x000000390000-0x000000800000 : "rootfs_data"
[ 0.450000] 0x000000050000-0x000000800000 : "firmware"
[ 0.470000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 40, using 40
[ 0.480000] TCP cubic registered
[ 0.490000] NET: Registered protocol family 17
[ 0.490000] 8021q: 802.1Q VLAN Support v1.8
[ 0.500000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.510000] Freeing unused kernel memory: 172k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 6.740000] JFFS2 notice: (351) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orp
han) and 8 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [ 8.920000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 8.920000] Backport based on wireless-testing.git master-2012-09-07
[ 8.930000] compat.git: wireless-testing.git
[ 8.980000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.990000] cfg80211: World regulatory domain updated:
[ 8.990000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.010000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.020000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.030000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.030000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.580000] SCSI subsystem initialized
[ 9.770000] usbcore: registered new interface driver usbfs
[ 9.770000] usbcore: registered new interface driver hub
[ 9.780000] usbcore: registered new device driver usb
[ 9.940000] lib80211: common routines for IEEE802.11 drivers
[ 10.650000] usbcore: registered new interface driver rt2500usb
[ 10.700000] phy0 -> rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT305X.eeprom'.
[ 10.880000] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 2872, rf: 0005, rev: 0200.
[ 10.930000] usbcore: registered new interface driver rt2800usb
[ 11.510000] PPP generic driver version 2.4.2
[ 11.750000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.060000] NET: Registered protocol family 24
[ 12.360000] nf_conntrack version 0.5.0 (467 buckets, 1868 max)
[ 12.950000] i2c /dev entries driver
[ 12.990000] dwc_otg: version 2.72a 24-JUN-2008
[ 12.990000] dwc_otg: Core Release: 2.66a
[ 13.200000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled
[ 13.200000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled
[ 13.210000] dwc_otg: Using DMA mode
[ 13.210000] dwc_otg: Device using Buffer DMA mode
[ 13.220000] dwc_otg dwc_otg.0: DWC OTG Controller
[ 13.220000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[ 13.230000] dwc_otg dwc_otg.0: irq 26, io mem 0x101c0000
[ 13.230000] dwc_otg: Init: Port Power? op_state=1
[ 13.240000] dwc_otg: Init: Power Port (0)
[ 13.240000] hub 1-0:1.0: USB hub found
[ 13.250000] hub 1-0:1.0: 1 port detected
[ 13.300000] i2c-gpio i2c-gpio.0: using pins 1 (SDA) and 2 (SCL)
[ 13.480000] Initializing USB Mass Storage driver...
[ 13.480000] usbcore: registered new interface driver usb-storage
[ 13.490000] USB Mass Storage support registered.
[ 16.800000] device eth0.1 entered promiscuous mode
[ 16.810000] device eth0 entered promiscuous mode
[ 16.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 16.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 18.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 20.240000] ramips-wdt: timeout value 60 must be 0 < timeout <= 40, using 40



BusyBox v1.19.4 (2012-10-13 02:55:36 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r33735)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet HWaddr C4:93:00:00:12:8F
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

eth0 Link encap:Ethernet HWaddr C4:93:00:00:12:8F
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1624 (1.5 KiB)
Interrupt:5

eth0.1 Link encap:Ethernet HWaddr C4:93:00:00:12:8F
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

eth0.2 Link encap:Ethernet HWaddr C4:93:00:00:12:8F
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:1608 (1.5 KiB)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

root@OpenWrt:/# iwconfig
eth0.1 no wireless extensions.

lo no wireless extensions.

eth0 no wireless extensions.

br-lan no wireless extensions.

eth0.2 no wireless extensions.

root@OpenWrt:/#