8devices Community https://www.8devices.com/community/ |
|
Rambutan boot loop https://www.8devices.com/community/viewtopic.php?f=22&t=1032 |
Page 1 of 1 |
Author: | albans81 [ 18 May 2017, 10:44 ] |
Post subject: | Rambutan boot loop |
Hi, after try to update rambutan board following instruction on Getting Started page i'm stuck in a boot loop. i have build image whit command ./build.sh rambutan and after copy the file /bin/ar71xx/openwrt-8devices-v2.9-ar71xx-nand-rambutan-initramfs-kernel.bin in a USB drive, and rename as 8dev_recovery.bin have i use wrong bin file? there is no sysupgrade file in folder. Any help? someone can give me a default image for restart the board? i am stuck in a boot loop. Serial output: U-Boot 2016.01-00030-g2fa4604 (Aug 18 2016 - 17:23:32 +0300) ========================================= Caraboot v3.1 (QCA9557, NAND) U-Boot http://www.8devices.com/ ----------------------------------------- DRAM: 128 MiB NAND: 128 MiB Net: eth0 Warning: eth0 MAC addresses don't match: Address in SROM is c4:93:00:07:6e:6b Address in environment is 00:19:55:66:77:89 , eth1 Warning: eth1 MAC addresses don't match: Address in SROM is c4:93:00:07:6e:6c Address in environment is 00:19:55:66:77:89 Hit <ESC> key to stop autoboot: 0 USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found USB1: USB EHCI 1.00 scanning bus 1 for devices... 1 USB Device(s) found 1 Storage Device(s) found ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** SCAN partition 1 Partition start 8064 size 30367872 name usbda1 Flashing image 8dev_recovery.bin (3863270 bytes) from usb device 0:1 Flashing image nand erase.part ubi; nand write 0x80060000 ubi 3af2e6 Erasing at 0x7fe0000 -- 100% complete.000, size 0x7a00000 0 OK NAND write: device 0 offset 0x600000, size 0x3af2e6 3863270 bytes written: OK Flashing sucsessful. Remove USB storage with recovery imag __________________sri____________________ 944x BootROM Ver. (asic) 1.0 [Nov 8 2011 13:42:57] _________________________________________ find_hif: bootstrap = 0x31c50 Nand Flash init otp_get_nand_table: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 ONFI: Control Setting = 0xb44 hdr: [0xbd004000 : 0xbd004000 : 0x2000 : 0x39fbdb14] nand_load_fw: read 4 pages nand_load_fw: 0x10000 0x800 0xbd0047f0 nand_load_fw: 0x20000 0x800 0xbd004ff0 nand_load_fw: 0x30000 0x800 0xbd0057f0 f/w 0 read complete, jumping to 0xbd004000 initialize PLL & DDR sri Scorpion 1.0 ath_ddr_initial_config(322): (16bit) ddr2 init ... done *** Warning *** : PCIe WLAN Module not found !!! *** Warning *** : PCIe WLAN Module not found !!! ... done fw1: Nand Init hdr:[0xbd004000 : 0xbd004000 : 0x2000 : 0x39fbdb14] nand_boot:skip 4 pages hdr:[0xa0100000 : 0xa0100000 : 0x81000 : 0x5c7a069a] nand_boot:read 258 pages f/w 1 read complete, jumping to 0xa0100000 U-Boot 2016.01-00030-g2fa4604 (Aug 18 2016 - 17:23:32 +0300) ========================================= Caraboot v3.1 (QCA9557, NAND) U-Boot http://www.8devices.com/ ----------------------------------------- DRAM: 128 MiB NAND: 128 MiB forever... THX |
Page 1 of 1 | All times are UTC |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |