8devices Community https://www.8devices.com/community/ |
|
Lima Industry wlan https://www.8devices.com/community/viewtopic.php?f=23&t=1053 |
Page 1 of 1 |
Author: | rraasch [ 15 Aug 2017, 12:24 ] |
Post subject: | Lima Industry wlan |
Using the Lima development board, the wlan works find, and broadcasts. Using the exact same settings on our custom board with the industry Lima, the wlan doesn't broadcast. Wed Jul 5 21:56:37 2017 daemon.notice netifd: radio0 (1074): Using interface wlan0 with hwaddr c4:93:XX:XX:XX:XX and ssid "Lima2" Wed Jul 5 21:56:37 2017 kern.info kernel: [ 22.007507] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Wed Jul 5 21:56:37 2017 kern.info kernel: [ 22.014114] br-lan: port 2(wlan0) entered forwarding state Wed Jul 5 21:56:37 2017 kern.info kernel: [ 22.019686] br-lan: port 2(wlan0) entered forwarding state Wed Jul 5 21:56:37 2017 daemon.notice netifd: radio0 (1074): wlan0: interface state ACS->ENABLED Wed Jul 5 21:56:37 2017 daemon.notice netifd: radio0 (1074): wlan0: AP-ENABLED Wed Jul 5 21:56:37 2017 daemon.notice netifd: Network device 'wlan0' link is up Wed Jul 5 21:56:39 2017 kern.info kernel: [ 24.013187] br-lan: port 2(wlan0) entered forwarding state root@OpenWrt:~# wifi status { "radio0": { "up": true, "pending": false, "autostart": true, "disabled": false, "config": { "path": "platform\/qca953x_wmac", "htmode": "HT20", "channel": "auto", "hwmode": "11ng" }, "interfaces": [ { "section": "@wifi-iface[0]", "ifname": "wlan0", "config": { "mode": "ap", "key": "12345678", "macfilter": "deny", "encryption": "psk2", "ssid": "Lima2", "mode": "ap", "network": [ "lan" ] } } ] } } Is there something I am doing wrong? |
Author: | rraasch [ 15 Aug 2017, 13:19 ] |
Post subject: | Re: Lima Industry wlan |
Does this have anything to do with SMART_ANT_CTL_2? Which is controlled by qca_mux_ctl.... |
Author: | rraasch [ 16 Aug 2017, 07:47 ] |
Post subject: | Re: Lima Industry wlan |
Furthermore, we only use one of the ethernet ports (eth0). What should eth1 be connected to? Can the pins float? |
Author: | gedass [ 16 Aug 2017, 07:49 ] |
Post subject: | Re: Lima Industry wlan |
Author: | gedass [ 16 Aug 2017, 07:57 ] |
Post subject: | Re: Lima Industry wlan |
Author: | rraasch [ 16 Aug 2017, 08:48 ] |
Post subject: | Re: Lima Industry wlan |
Thanks for the reply. The datasheet I have does not have that information. Could you direct me to the datasheet you are referring to? http://www.8devices.com/media/products/ ... asheet.pdf |
Author: | rraasch [ 16 Aug 2017, 09:26 ] |
Post subject: | Re: Lima Industry wlan |
WRT our WLAN antenna issues. Do you have any ideas? I have now attached two pigtail antennas to the module. They don't seem to help our issue. Do I need to select these, and not the board antenna (just ANT0/1 float)? |
Author: | gedass [ 16 Aug 2017, 14:23 ] |
Post subject: | Re: Lima Industry wlan |
There are no differences between commercial an industrial modules.Only extended temperature range.Maybe your module is faulty ? |
Page 1 of 1 | All times are UTC |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |