8devices Community https://www.8devices.com/community/ |
|
USB2can Issues with one car https://www.8devices.com/community/viewtopic.php?f=16&t=1091 |
Page 1 of 2 |
Author: | gedass [ 22 Jan 2018, 17:34 ] |
Post subject: | Re: USB2can Issues with one car |
Hi, can you try to read data running in Windows mode ? (canal driver). Linux driver has a bug in high speed data mode. Did you try the other manufacturer converter ? Bad thing that I don't have similar can so I can't check. What is the Kia can bus speed ? Is it yours post: http://jas-hacks.blogspot.lt/2017/01/im ... hicle.html nulleight15 May 2017 at 16:34 Hi, thanks, I got it working at 500kBps. Do I understand correctly, that I now have to open communication channel using VW TP 2.0 before I see anything? For now I only see one strange message repeated indefinitely: 0x17F00010 with data bytes 20 10 00 00 00 00 00 10 Thanks for your answer, Konstantin |
Author: | rootadmin [ 22 Jan 2018, 22:14 ] |
Post subject: | Re: USB2can Issues with one car |
Hi, No that wasn’t my post although looks like the same issue. I haven’t tried it on windows yet, however I also have the CANtact which gives the same issues on the skoda yet reads it on the Kia, both speeds weee set to 500 however I’ve tried the skoda on all the main ones. The only time I’ve had any data returned was when I connected the usb2can via a Y cable to a vcds and looked at the data being sent to the vcds, however it still did not give me anything useful. I’ll try windows tomorrow but not holding much hope. |
Author: | rootadmin [ 23 Jan 2018, 19:49 ] |
Post subject: | Re: USB2can Issues with one car |
So a bit more digging. Tried it today with windows no change, tried it in conjunctiok with Kayak = no change. The VAG obd port will only send data which is requested by an approved (with a handshake), looks like candy no and cansniffer are totally no goes. Basically short of tapping into the wiring prior to the can gateway module I think I’m “totally” outa luck. |
Author: | SPlatten [ 25 Jan 2018, 08:48 ] |
Post subject: | Re: USB2can Issues with one car |
I have a similar problem, I purchased a USB2CAN device to sniff data on my Audi A5, i've got the correct cable, but I see nothing, this post was added to my own query, is there a way around this? If this is a show stopper then why isn't this detail mentioned on the device page so potential purchasers are aware of this limitation? |
Author: | gedass [ 25 Jan 2018, 17:59 ] |
Post subject: | Re: USB2can Issues with one car |
Do not you see any data from can bus ? |
Author: | SPlatten [ 26 Jan 2018, 07:40 ] |
Post subject: | Re: USB2can Issues with one car |
Nothing at all. The post by "rootadmin" looks like a similar issue. |
Author: | gedass [ 26 Jan 2018, 08:41 ] |
Post subject: | Re: USB2can Issues with one car |
But "rootadmin" see message like "0x17F00010 with data bytes 20 10 00 00 00 00 00 10" from a CAN bus. |
Author: | SPlatten [ 26 Jan 2018, 09:19 ] |
Post subject: | Re: USB2can Issues with one car |
I'm not getting anything, I am running Windows and Linux in VirtualBox on a mackBook Pro, could that be an issue? |
Author: | rootadmin [ 28 Jan 2018, 09:02 ] |
Post subject: | Re: USB2can Issues with one car |
Just another wee update, the only time I can see any real information -and by information I mean 2 lines in cansniffer is when I was using a Y cable with vcds as that handshakes with TP2.0 Perhaps a new firmware will be released which will allow connection to bag cars but I really feel that this should have been started prior to purchase that it will not read data on new vag models (unless I am in error of course). |
Page 1 of 2 | All times are UTC |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |