www.8devices.com
View unanswered posts | View active topics It is currently 23 Jan 2018, 02:28



Reply to topic  [ 1 post ] 
 WiFi only Mode 
Author Message

Joined: 19 Dec 2017, 07:16
Posts: 1
I have developed customised board based on Rambutan Development Kit.
In this board, i have removed WAN & LAN Ethernet circuitry. I want to use this module WiFi Repeater Mode.

I have enabled wifi in "/etc/config/wireless". But I unable to see my WiFi.
I also tried to modify "/etc/config/network" to remove 'br-lan' and only enable wlan interface.

So how to enable WiFi as ap mode?

Below is the boot log.
Code:
__________________sri____________________
944x BootROM Ver. (asic) 1.0 [Nov  8 2011 13:42:57]
_________________________________________
find_hif: bootstrap = 0x31c10
Nand Flash init
otp_get_nand_table: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
ONFI: Control Setting = 0xb44
hdr: [0xbd004000 : 0xbd004000 : 0x2000 : 0x39fbdb14]
nand_load_fw: read 4 pages
nand_load_fw: 0x10000 0x800 0xbd0047f0
nand_load_fw: 0x20000 0x800 0xbd004ff0
nand_load_fw: 0x30000 0x800 0xbd0057f0
f/w 0 read complete, jumping to 0xbd004000
initialize PLL & DDR

sri
Scorpion 1.0
ath_ddr_initial_config(322): (16bit) ddr2 init
... done
*** Warning *** : PCIe WLAN Module not found !!!
... done
fw1: Nand Init
hdr:[0xbd004000 : 0xbd004000 : 0x2000 : 0x39fbdb14]
nand_boot:skip 4 pages
hdr:[0xa0100000 : 0xa0100000 : 0x81000 : 0x5c7a069a]
nand_boot:read 258 pages
f/w 1 read complete, jumping to 0xa0100000


U-Boot 2016.01-00030-g2fa4604 (Aug 18 2016 - 17:23:32 +0300)

=========================================
Caraboot v3.1 (QCA9557, NAND) U-Boot
http://www.8devices.com/
-----------------------------------------
DRAM:  128 MiB
NAND:  128 MiB
Net:   eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         c4:93:00:07:66:73
Address in environment is  00:19:55:66:77:89
, eth1
Warning: eth1 MAC addresses don't match:
Address in SROM is         c4:93:00:07:66:74
Address in environment is  00:19:55:66:77:89

Hit <ESC> key to stop autoboot:  0
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=3", size 122 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 976, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1493900931
ubi0: available PEBs: 0, total reserved PEBs: 976, PEBs reserved for bad PEB handling: 20
Read 0 bytes from volume kernel to 82000000
No size specified -> Using max size (1523712)
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   MIPS OpenWrt Linux-4.1.23
   Created:      2016-06-28   8:09:52 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1423424 Bytes = 1.4 MiB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
[    0.000000] Linux version 4.1.23 (builder@openwrt-buildbot-2) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 unknown) ) #1 Tue Jun 28 16:32:15 UTC 2016
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=RAMBUTAN mtdparts=ar934x-nfc:3M(u-boot)ro,2M(u-boot-env)ro,1M(art)ro,122M(ubi) console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124888K/131072K available (3250K kernel code, 150K rwdata, 768K rodata, 236K init, 199K bss, 6184K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:83
[    0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008287] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.071186] pid_max: default: 32768 minimum: 301
[    0.076193] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.083235] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092997] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.104418] NET: Registered protocol family 16
[    0.110286] MIPS: machine is 8devices Rambutan board
[    0.116098] ar724x-pci ar724x-pci.0: PCIe link is down
[    0.121565] registering PCI controller with io_map_base unset
[    0.127819] ar724x-pci ar724x-pci.1: PCIe link is down
[    0.133281] registering PCI controller with io_map_base unset
[    0.587254] PCI host bridge to bus 0000:00
[    0.591659] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.598970] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.604901] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.612117] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.620687] PCI host bridge to bus 0000:01
[    0.625046] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[    0.632369] pci_bus 0000:01: root bus resource [io  0x0001]
[    0.638291] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[    0.645513] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.654662] Switched to clocksource MIPS
[    0.660000] NET: Registered protocol family 2
[    0.665483] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.672905] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.679721] TCP: Hash tables configured (established 1024 bind 1024)
[    0.686569] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.692792] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.699735] NET: Registered protocol family 1
[    0.705283] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.726704] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.732912] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.745583] io scheduler noop registered
[    0.749761] io scheduler deadline registered (default)
[    0.755555] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.764650] console [ttyS0] disabled
[    0.788540] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.797725] console [ttyS0] enabled
[    0.797725] console [ttyS0] enabled
[    0.805142] bootconsole [early0] disabled
[    0.805142] bootconsole [early0] disabled
[    0.814013] ar933x-uart: ttyATH0 at MMIO 0x18500000 (irq = 14, base_baud = 2500000) is a AR933X UART
[    0.828527] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[    0.835011] nand: AMD/Spansion NAND 128MiB 3,3V 8-bit
[    0.840134] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.847855] Scanning device for bad blocks
[    0.939565] 4 cmdlinepart partitions found on MTD device ar934x-nfc
[    0.945929] Creating 4 MTD partitions on "ar934x-nfc":
[    0.951141] 0x000000000000-0x000000300000 : "u-boot"
[    0.956953] 0x000000300000-0x000000500000 : "u-boot-env"
[    0.962972] 0x000000500000-0x000000600000 : "art"
[    0.968427] 0x000000600000-0x000008000000 : "ubi"
[    0.984813] libphy: ag71xx_mdio: probed
[    0.996986] libphy: ag71xx_mdio: probed
[    1.586418] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd023, driver=Generic PHY]
[    1.596252] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.266200] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.1:00 [uid=004dd074, driver=Atheros 8031/8033 ethernet]
[    2.277377] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[    2.285042] NET: Registered protocol family 10
[    2.292417] NET: Registered protocol family 17
[    2.297051] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.309887] Bridge firewalling registered
[    2.314075] 8021q: 802.1Q VLAN Support v1.8
[    2.321680] UBI: auto-attach mtd3
[    2.324921] ubi0: attaching mtd3
[    3.066351] random: nonblocking pool is initialized
[    4.194501] ubi0: scanning is finished
[    4.218175] ubi0: attached mtd3 (name "ubi", size 122 MiB)
[    4.223741] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.230751] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.237645] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.244708] ubi0: good PEBs: 976, bad PEBs: 0, corrupted PEBs: 0
[    4.250799] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    4.258131] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1493900931
[    4.267402] ubi0: available PEBs: 0, total reserved PEBs: 976, PEBs reserved for bad PEB handling: 20
[    4.276807] ubi0: background thread "ubi_bgt0d" started, PID 271
[    4.284567] block ubiblock0_1: created from ubi0:1(rootfs)
[    4.290181] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[    4.297280] hctosys: unable to open rtc device (rtc0)
[    4.309632] VFS: Mounted root (squashfs filesystem) readonly on device 254:1.
[    4.318175] Freeing unused kernel memory: 236K (80475000 - 804b0000)
[    5.605836] init: Console is alive
[    5.609473] init: - watchdog -
[    6.835872] usbcore: registered new interface driver usbfs
[    6.841514] usbcore: registered new interface driver hub
[    6.847003] usbcore: registered new device driver usb
[    6.861531] SCSI subsystem initialized
[    6.870907] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.878843] ehci-platform: EHCI generic platform driver
[    6.884219] ehci-platform ehci-platform.0: EHCI Host Controller
[    6.890292] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[    6.900579] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[    6.906693] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[    6.924681] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[    6.931918] hub 1-0:1.0: USB hub found
[    6.936069] hub 1-0:1.0: 1 port detected
[    6.940367] ehci-platform ehci-platform.1: EHCI Host Controller
[    6.946440] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[    6.956757] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[    6.962860] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[    6.984675] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[    6.991940] hub 2-0:1.0: USB hub found
[    6.996061] hub 2-0:1.0: 1 port detected
[    7.004041] usbcore: registered new interface driver usb-storage
[    7.011638] init: - preinit -
[    7.688807] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   10.935496] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 422
[   11.058958] UBIFS (ubi0:2): recovery needed
[   11.315970] UBIFS (ubi0:2): recovery completed
[   11.320555] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[   11.328517] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.338580] UBIFS (ubi0:2): FS size: 115294208 bytes (109 MiB, 908 LEBs), journal size 5713920 bytes (5 MiB, 45 LEBs)
[   11.349337] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[   11.356058] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID DFFBB38A-D494-4EFF-98D5-724AA68FD211, small LPT model
[   11.376069] mount_root: switching to jffs2 overlay
[   11.416218] procd: - early -
[   11.419231] procd: - watchdog -
[   11.978926] procd: - ubus -
[   12.102255] procd: - init -
Please press Enter to activate this console.
[   12.903444] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.918677] i2c /dev entries driver
[   12.929457] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[   12.937006] Backport generated by backports.git backports-20151218-0-g2f58d9d
[   12.947410] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.962185] nf_conntrack version 0.5.0 (1955 buckets, 7820 max)
[   12.985738] Driver for 1-wire Dallas network protocol.
[   13.011590] xt_time: kernel timezone is -0000
[   13.069127] PPP generic driver version 2.4.2
[   13.075759] NET: Registered protocol family 24
[   13.118650] ath9k qca955x_wmac: firmware, attempted to load /lib/firmware/soc_wmac.eeprom, but failed with error -22
[   13.129378] ath9k qca955x_wmac: Direct firmware load for soc_wmac.eeprom failed with error -22
[   13.138115] ath9k qca955x_wmac: Falling back to user helper
[   13.167108] firmware soc_wmac.eeprom: firmware_loading_store: map pages failed
[   13.175001] ath: phy0: Unable to load EEPROM file soc_wmac.eeprom
[   13.181197] ath9k qca955x_wmac: failed to initialize device
[   13.186920] ath9k: probe of qca955x_wmac failed with error -22
[   19.885743] device eth0 entered promiscuous mode
[   19.891686] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   19.946327] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready




BusyBox v1.24.2 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 DESIGNATED DRIVER (v2.9, unknown)
 -----------------------------------------------------
  * 2 oz. Orange Juice         Combine all juices in a
  * 2 oz. Pineapple Juice      tall glass filled with
  * 2 oz. Grapefruit Juice     ice, stir well.
  * 2 oz. Cranberry Juice
 -----------------------------------------------------
root@Rambutan:/#
root@Rambutan:/#


19 Dec 2017, 07:33
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 1 post ] 

Who is online

Users browsing this forum: No registered users


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

Protected by Anti-Spam ACP Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software.