www.8devices.com
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Author |
Message |
rraasch
Joined: 17 May 2017, 11:02 Posts: 12
|
Using the Lima development board, the wlan works find, and broadcasts.
Using the exact same settings on our custom board with the industry Lima, the wlan doesn't broadcast.
Wed Jul 5 21:56:37 2017 daemon.notice netifd: radio0 (1074): Using interface wlan0 with hwaddr c4:93:XX:XX:XX:XX and ssid "Lima2" Wed Jul 5 21:56:37 2017 kern.info kernel: [ 22.007507] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Wed Jul 5 21:56:37 2017 kern.info kernel: [ 22.014114] br-lan: port 2(wlan0) entered forwarding state Wed Jul 5 21:56:37 2017 kern.info kernel: [ 22.019686] br-lan: port 2(wlan0) entered forwarding state Wed Jul 5 21:56:37 2017 daemon.notice netifd: radio0 (1074): wlan0: interface state ACS->ENABLED Wed Jul 5 21:56:37 2017 daemon.notice netifd: radio0 (1074): wlan0: AP-ENABLED Wed Jul 5 21:56:37 2017 daemon.notice netifd: Network device 'wlan0' link is up Wed Jul 5 21:56:39 2017 kern.info kernel: [ 24.013187] br-lan: port 2(wlan0) entered forwarding state
root@OpenWrt:~# wifi status { "radio0": { "up": true, "pending": false, "autostart": true, "disabled": false, "config": { "path": "platform\/qca953x_wmac", "htmode": "HT20", "channel": "auto", "hwmode": "11ng" }, "interfaces": [ { "section": "@wifi-iface[0]", "ifname": "wlan0", "config": { "mode": "ap", "key": "12345678", "macfilter": "deny", "encryption": "psk2", "ssid": "Lima2", "mode": "ap", "network": [ "lan" ] } } ] } }
Is there something I am doing wrong?
|
15 Aug 2017, 12:24 |
|
|
rraasch
Joined: 17 May 2017, 11:02 Posts: 12
|
Does this have anything to do with SMART_ANT_CTL_2? Which is controlled by qca_mux_ctl....
|
15 Aug 2017, 13:19 |
|
|
rraasch
Joined: 17 May 2017, 11:02 Posts: 12
|
Furthermore, we only use one of the ethernet ports (eth0). What should eth1 be connected to? Can the pins float?
|
16 Aug 2017, 07:47 |
|
|
gedass
Joined: 07 Dec 2011, 16:01 Posts: 525 Location: Lithuania
|
|
16 Aug 2017, 07:49 |
|
|
gedass
Joined: 07 Dec 2011, 16:01 Posts: 525 Location: Lithuania
|
|
16 Aug 2017, 07:57 |
|
|
rraasch
Joined: 17 May 2017, 11:02 Posts: 12
|
Thanks for the reply. The datasheet I have does not have that information. Could you direct me to the datasheet you are referring to? http://www.8devices.com/media/products/ ... asheet.pdf
|
16 Aug 2017, 08:48 |
|
|
rraasch
Joined: 17 May 2017, 11:02 Posts: 12
|
WRT our WLAN antenna issues. Do you have any ideas?
I have now attached two pigtail antennas to the module. They don't seem to help our issue. Do I need to select these, and not the board antenna (just ANT0/1 float)?
|
16 Aug 2017, 09:26 |
|
|
gedass
Joined: 07 Dec 2011, 16:01 Posts: 525 Location: Lithuania
|
There are no differences between commercial an industrial modules.Only extended temperature range.Maybe your module is faulty ?
|
16 Aug 2017, 14:23 |
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: No registered users |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|